Knowing how to clean a dryer vent is one of the most important home safety skills you can have. The U.S. Fire Administration reports that failure to clean was the leading factor contributing to the ignition of clothes dryer fires in homes from 2018 to 2020. Lint is highly flammable, and when it builds up in the vent, hot air can’t escape, the dryer runs hotter and longer, and the risk of fire rises.
This guide shows you how to clean a dryer vent in eight easy steps, the tools that work, how often to do it, and the warning signs that mean you should call a professional.
Key takeaways
- Clean the lint screen every load and the full dryer vent at least once a year, more with heavy use.
- A dryer vent brush kit on flexible rods, a vacuum and a screwdriver handle most vents.
- Clean from both ends: the dryer side and the exterior hood.
- Replace foil or vinyl transition ducts with semi-rigid or rigid metal while you’re at it.

In this guide
Why dryer vent cleaning matters
Every load of laundry sheds lint. The lint screen catches most of it, but some always passes into the vent. Over months, lint lines the duct, collects at bends and builds up behind the exterior flap. The result:
- Fire risk. Lint is a ready fuel, and a clogged vent traps heat.
- Longer drying times. Clothes take two cycles instead of one. See dryer not drying clothes.
- Higher energy bills from longer run times.
- Wear on the dryer as heating elements and thermal fuses work harder.
- Carbon monoxide risk with gas dryers if exhaust can’t escape properly.
Tools you need
| Tool | Why |
|---|---|
| Dryer vent brush kit with flexible rods | Reaches through the full duct run |
| Vacuum with hose and crevice tool | Removes loosened lint |
| Lint trap brush (long, thin) | Cleans the lint screen housing |
| Screwdriver or nut driver | Removes clamps and the exterior hood |
| Foil tape (UL 181 or dryer-rated) | Reseals joints |
| Work gloves, dust mask, flashlight | Comfort and safety |
| Replacement semi-rigid metal transition duct | If yours is foil or vinyl |
Many vent brush kits connect to a cordless drill so the brush spins as it goes. Use the drill on low speed and in the clockwise direction so the rod sections don’t unscrew inside the duct.
How to clean a dryer vent in 8 easy steps
Step 1: Unplug the dryer and shut off gas
Unplug an electric dryer. For a gas dryer, turn off the gas valve behind it, and be careful not to kink or strain the gas line when you move the dryer.
Step 2: Clean the lint screen and housing
Remove the lint screen and wash it with warm, soapy water if it has a film from dryer sheets. Use a long lint trap brush and vacuum to clean the slot the screen fits into. A surprising amount of lint collects inside it.
Step 3: Pull the dryer out and disconnect the transition duct
Slide the dryer forward. Loosen the clamp and pull the transition duct (the short flexible duct between the dryer and the wall) off the dryer’s exhaust outlet and the wall connection.
Step 4: Clean the dryer’s exhaust outlet
Vacuum lint from the outlet on the back of the dryer and reach in as far as you safely can.
Step 5: Brush the vent from the inside
Feed the brush into the wall duct, adding rod sections as you go. Push and twist slowly through the entire run, then pull back, letting lint fall out. Vacuum as it comes out. Repeat until little lint comes back.
Step 6: Clean the exterior vent hood
Go outside and find the vent hood. Remove any lint around the flap or louvers, and brush or vacuum the duct from the outside end. Make sure the damper flap opens and closes freely. Remove any bird nests. Exterior hoods should not have screens, which trap lint.
Step 7: Replace or reattach the transition duct
If your transition duct is foil or vinyl, replace it with semi-rigid or rigid metal, as close to straight and short as possible. Foil and plastic ducts crush easily and are a known fire concern; the U.S. Fire Administration advises replacing coiled-wire foil or plastic venting with rigid, non-ribbed metal duct. Secure both ends with clamps and seal with foil tape, not screws that protrude into the duct.
Step 8: Test the airflow
Push the dryer back without crushing the duct, plug it in, restore gas and run it on air fluff. Go outside: you should feel strong, steady airflow from the hood. Then run a normal load and compare drying time with before.
Use a dryer vent periscope or recessed box if the dryer sits close to the wall. These let the transition duct connect without being crushed.
How often to clean a dryer vent
| Household | Full vent cleaning |
|---|---|
| 1–2 people, light laundry | Once a year |
| Family of 4+ or daily loads | Every 6 months |
| Pets, lots of towels or bedding | Every 6 months |
| Long vent runs or roof vents | Every 6 months, check more often |
| Any warning sign | Now |
Clean the lint screen before or after every load. See clogged dryer vent for the warning signs.
When to call a professional
- The vent run is long, has many bends or exits through the roof. See roof dryer vent.
- You can’t get the brush through, or it hits a blockage.
- The duct is crushed, disconnected inside the wall or made of plastic or foil inside walls.
- You smell burning, or the dryer shuts off on its own.
- Gas dryers show any sign of exhaust problems.
Professional dryer vent cleaning usually costs about $100 to $300. See dryer vent cleaning cost.
Check the vent length while you’re there
Long vent runs collect lint faster and reduce airflow. The International Residential Code limits typical 4-inch dryer exhaust ducts to 35 feet, reduced for each elbow, unless the dryer manufacturer allows more. Check yours with our dryer vent length calculator.
A worked example
A family of five notices towels need two cycles and the laundry room gets humid. The lint screen is clean, but the foil transition duct is crushed behind the dryer and the exterior flap is held half-open by packed lint. They brush the 18-foot vent from both ends, pulling out several handfuls of lint, replace the foil duct with semi-rigid aluminum and clear the hood. Towels dry in one cycle again, and the dryer runs about 20 minutes less per load.
How to clean a dryer vent: FAQ
How do I know if my dryer vent needs cleaning?
Long drying times, a hot dryer or laundry room, a burning smell, lint around the exterior hood and a flap that doesn’t open are common signs.
Can I use a leaf blower to clean a dryer vent?
Some people blow out short, straight vents from the inside, but a brush and vacuum are more thorough and less messy. Never use a leaf blower on a vent with a crushed or disconnected section.
Is dryer vent cleaning worth it?
Yes. It reduces fire risk, shortens drying times and saves energy.
How long does it take to clean a dryer vent?
Usually 30 to 60 minutes for a typical wall vent.
Should I clean the inside of the dryer too?
The cabinet can collect lint around the drum and heating element. Cleaning inside the cabinet is best done by an appliance technician, especially on gas dryers.
The bottom line
Learning how to clean a dryer vent takes an hour and pays off in safety, faster drying and lower bills. Clean the lint screen every load, brush the full vent at least once a year from both ends, replace foil or plastic transition ducts with metal, and make sure the exterior flap opens freely. For more safety tips, see the U.S. Fire Administration’s appliance fire safety page.
