We research products independently. When you buy through our links we may earn a commission. How we make money
Dryer vents

How to Clean Dryer Lint Trap: 5 Simple Steps Plus the Deep Clean Most People Miss

Knowing how to clean dryer lint trap screens properly is the simplest dryer fire prevention step there is. Most people peel off the visible lint after each load, which is the right habit. But two things often get missed: an invisible film from dryer sheets and fabric softener that clogs the mesh, and lint that collects in the lint trap housing below the screen.

This guide covers five simple steps for everyday cleaning, the monthly deep clean, and how to test whether your lint screen is actually letting air through.

Key takeaways

  • Remove lint from the screen before or after every load.
  • Wash the screen with warm water, dish soap and a soft brush every month or two, or whenever water beads on it.
  • Vacuum the lint trap housing every few months with a narrow attachment.
  • A clean dryer lint trap doesn’t replace cleaning the vent itself.

In this guide

Why the lint trap matters

The lint screen catches most of the fibers shed by clothes during drying. Lint that gets past it collects in the dryer’s internal ducting and the exhaust vent. The USFA identifies failure to clean as the leading factor in home clothes dryer fires and recommends cleaning the lint filter before or after each load. See the USFA’s dryer safety guidance.

A clogged lint screen also restricts airflow, so clothes take longer to dry and the dryer uses more energy. See dryer not drying clothes.

Everyday cleaning: 5 simple steps

  1. Pull out the lint screen. It’s usually inside the door opening or on top of the dryer.
  2. Roll the lint off with your fingers, starting from one edge. It usually comes away in a sheet.
  3. Check both sides of the screen for stuck lint.
  4. Wipe the slot around the screen opening with your hand or a dry cloth to catch any lint that fell in.
  5. Slide the screen back in fully. Never run the dryer without it.

Do this before or after every load.

The monthly deep clean

Dryer sheets and liquid fabric softener leave a waxy coating on the screen. It’s often invisible, but it can block much of the mesh.

The water test

Hold the clean screen under the tap. If water pools on top or beads instead of running through, the mesh is coated.

How to wash it

  1. Remove the lint.
  2. Wet the screen with warm water.
  3. Add a few drops of dish soap and scrub both sides gently with a soft brush, such as a soft toothbrush or nylon brush.
  4. Rinse well and run the water test again. Water should flow straight through.
  5. Let the screen dry completely before putting it back.

Do this every month or two, or more often if you use dryer sheets.

Clean the lint trap housing

Lint falls past the screen into the housing below it. Over months, it builds up where you can’t see it.

  1. Unplug the dryer.
  2. Remove the lint screen.
  3. Use a vacuum with a narrow crevice tool, or a long, flexible lint brush made for dryers, to reach down into the housing.
  4. Vacuum until no more lint comes out.

Do this every three to six months. Some dryers allow you to remove a cover screw to access the housing more easily; check your manual.

Lint trap vs vent cleaning

Task How often
Remove lint from screen Every load
Wash lint screen Every 1 – 2 months
Vacuum lint trap housing Every 3 – 6 months
Clean the full dryer vent At least once a year

The lint screen catches most lint, not all of it. See our main guide, how to clean a dryer vent, and dryer fire prevention.

Signs your lint screen isn’t doing its job

  • Lint on clothes after drying.
  • Long drying times.
  • Lint building up around the dryer or at the exterior hood.
  • A torn or bent screen. Replace damaged screens; they’re inexpensive and model-specific.

Dryer sheets and lint

You don’t have to stop using dryer sheets, but wash the screen more often if you use them. Wool dryer balls are an alternative that doesn’t coat the screen.

Lint trap designs differ

Not all dryers have the same lint trap:

Design Where it is Cleaning tips
Door-mounted screen Inside the door opening, at the bottom Pull straight up; check the slot below for lint
Top-mounted screen On top of the dryer, toward the back Pull up; vacuum the slot with a long crevice tool
Two-part or folding screen Inside the door Open both sides to clean
Heat pump or condenser dryer filters Door and sometimes a second filter near the base Clean both; some also need the condenser rinsed

Check your dryer manual for the exact design and any second filter.

How to replace a damaged lint screen

Lint screens can tear, bend or lose their frame. A damaged screen lets lint into the dryer’s internal ducting. Replacement screens are model-specific, so:

  1. Find the model number, usually on a label inside the door or on the back.
  2. Order a genuine or compatible replacement screen for that model.
  3. Slide the new screen in fully.

Lint around the dryer

If you find lint collecting under or behind the dryer, it may be escaping from the lint trap housing, a gasket or a disconnected vent. Check the transition duct behind the dryer, and have an appliance technician check internal ducts and seals if lint keeps appearing. See clogged dryer vent.

A simple monthly habit

Pair washing the lint screen with another monthly task, such as checking the HVAC air filter. Learning how to clean dryer lint trap screens properly takes five minutes and improves drying times, energy use and fire safety.

How to clean dryer lint trap FAQ

How often should I clean my dryer lint trap?

Remove lint every load and wash the screen every month or two.

Why does water not go through my lint screen?

A film from dryer sheets or fabric softener is coating the mesh. Wash it with dish soap and a brush.

Can I run the dryer without the lint screen?

No. Lint will go straight into the dryer’s internal ducting and the vent.

How do I clean lint deep inside the dryer?

Vacuum the lint trap housing with a narrow attachment or flexible lint brush. For internal ducting, call an appliance technician.

Should I replace a torn lint screen?

Yes. A torn screen lets lint through.