We research products independently. When you buy through our links we may earn a commission. How we make money
Sealing & insulation

Duct Leakage Test: 6 Simple Facts About Duct Blaster Testing

Duct leakage test: Duct Leakage Test: 6 Simple Facts About Duct Blaster Testing
Photo: RDNE Stock project / Pexels

A duct leakage test tells you exactly how leaky your duct system is, in numbers instead of guesses. Energy auditors and HVAC contractors use a calibrated fan, usually called a duct blaster, to pressurize the ducts and measure how much air escapes. It’s the basis for most energy code compliance, utility rebates and before-and-after proof that duct sealing worked.

This guide covers six simple facts about duct leakage testing: how the test works, what the results mean, what’s considered good, what it costs, how to prepare, and how to use the numbers.

Key takeaways

  • A duct leakage test pressurizes the duct system, usually to 25 pascals, and measures leakage in CFM25.
  • “Total leakage” includes leaks into the house; “leakage to outside” is the part that wastes energy.
  • Tests typically cost about $150 to $400, and are often included with professional sealing.
  • Test before and after sealing to see exactly what improved.
Duct leakage test example in a home
Photo by Guy Dwelly on Pexels
In this guide

Fact 1: How a duct blaster test works

The technician:

  1. Turns off the HVAC system and removes the filter.
  2. Seals every supply register and return grille with tape or plastic covers.
  3. Connects a calibrated fan (the duct blaster) to the system, usually at the air handler or a large return grille.
  4. Runs the fan to pressurize the ducts to a standard test pressure, commonly 25 pascals (about 0.1 inch of water column).
  5. Reads how much airflow the fan needs to hold that pressure. That airflow equals the leakage.

The result is reported in CFM25: cubic feet per minute of leakage at 25 pascals. The test takes about an hour for a typical home.

Fact 2: Total leakage vs leakage to outside

There are two main ways to measure:

Test What it measures How
Total duct leakage All leaks, including into conditioned space Duct blaster alone
Leakage to outside Only leaks to attics, crawlspaces, garages and outdoors Duct blaster plus a blower door pressurizing the house to the same pressure

Leakage to outside is what costs you energy, because air leaking into conditioned rooms isn’t lost. Leakage to outside requires a blower door as well, so the test takes a bit longer. Many energy programs specify one or both.

Fact 3: What the numbers mean

Raw CFM25 is hard to interpret on its own, so results are often normalized:

  • CFM25 per 100 square feet of conditioned floor area. A common benchmark for codes and programs.
  • Percentage of system airflow. Leakage compared with the air the blower moves (around 400 CFM per ton).

As reference points, ENERGY STAR’s new-home program limits leakage to outside to the greater of 4 CFM25 per 100 square feet of conditioned floor area or 40 CFM25, and sets total leakage limits at rough-in of roughly 8 to 12 CFM25 per 100 square feet depending on the number of returns. Older existing homes often test several times higher. A ballpark way to read your results:

Leakage to outside (CFM25 per 100 sq ft) Rough meaning
Under 4 Very tight, new-home level
4 – 8 Good for an existing home
8 – 15 Leaky; sealing likely pays back
Over 15 Very leaky; look for disconnections

Your tester should explain your results in context, including where the ducts run and your climate.

Fact 4: When you need a duct leakage test

  • Before and after duct sealing, to know what you’re paying for and to verify results.
  • For utility rebates, which often require testing by an approved contractor.
  • For energy code compliance on new homes, additions and HVAC replacements in many areas.
  • When diagnosing comfort problems, like rooms that never get enough air.
  • During a home energy audit, along with a blower door test of the whole house.
  • Before buying a home, if the ducts are in an attic or crawlspace and comfort or bills are a concern.

Fact 5: What a duct leakage test costs

Service Typical cost
Duct leakage test alone $150 – $400
Duct test plus blower door (leakage to outside) $250 – $500
Full home energy audit with testing $300 – $700
Testing included with duct sealing Often part of the quote

Some utilities subsidize energy audits heavily. Aerosol sealing jobs such as Aeroseal include before-and-after testing as part of the process.

Fact 6: How to prepare for the test

  1. Make the air handler and filter easy to reach.
  2. Clear furniture away from registers and returns.
  3. Make sure attic, crawlspace and basement access is clear.
  4. Tell the tester about any rooms with comfort problems.
  5. Keep windows and exterior doors closed during the test.
  6. Turn off combustion appliances if the tester asks, and keep pets away from the equipment.

Using your results

A good tester won’t just hand you a number. They’ll help you find where the leakage is. Common techniques include feeling and smoke-testing joints while the ducts are pressurized, and using a thermal camera when there’s a temperature difference.

Then the fixes follow:

Then test again. Seeing the number fall is the best proof a sealing job worked.

Estimate the cost of your leakage. Plug your bill and estimated leakage into our leaky duct cost calculator to see roughly what sealing could save and how fast it pays back.

A worked example

A 2,000-square-foot home tests at 360 CFM25 of leakage to outside, or 18 CFM25 per 100 square feet: very leaky. The tester finds a disconnected flex run in the attic and failed tape at most takeoffs. After the run is reconnected and every reachable joint is sealed with mastic, the retest shows 110 CFM25, or 5.5 per 100 square feet. That’s a 70 percent reduction, measured, not guessed. The homeowners notice stronger airflow upstairs within a day.

Duct leakage test vs blower door test

People often confuse the two. A blower door test measures how leaky the whole house is: walls, windows, attic floor and everything else. A duct leakage test measures only the duct system. Used together, they let a tester calculate leakage to outside, which is the duct leakage that actually costs you energy.

If you’re planning a broader energy upgrade, such as air sealing the attic floor, adding insulation and sealing ducts, ask for both tests. The blower door results guide house air sealing; the duct results guide duct work. Doing both at the same visit is usually cheaper than booking them separately.

Questions to ask the tester

  1. Will you test total leakage, leakage to outside, or both?
  2. What test pressure and standard will you use?
  3. Can you show me where the biggest leaks are while the ducts are pressurized?
  4. How do my numbers compare with code or program targets?
  5. Will you retest after sealing, and is that included?
  6. Can you perform a combustion safety test at the same visit?

Clear, specific answers are a good sign that you’ll get useful results rather than just a number on a form.

DIY alternatives to a professional test

You can’t measure leakage accurately without calibrated equipment, but you can find many leaks:

  • Feel joints with a damp hand while the fan runs.
  • Use an incense stick to watch for drafts.
  • Look for dust streaks on insulation near joints.
  • Compare airflow at registers; very weak registers may sit downstream of a leak.

These help you fix the obvious problems. A professional test tells you how much is left.

Safety after sealing

A tighter duct system changes pressures in your home. ENERGY STAR recommends a combustion safety test after duct sealing in homes with gas or oil appliances, to make sure flues still draft properly. Many testers can do this at the same visit. See furnace carbon monoxide safety for more.

Duct leakage test: FAQ

What is a duct blaster?

A calibrated fan and pressure gauge used to pressurize a home’s duct system and measure how much air leaks out.

What is CFM25?

Cubic feet per minute of air leakage measured when the ducts are pressurized to 25 pascals.

How long does a duct leakage test take?

About an hour for total leakage; a little longer for leakage to outside, which also uses a blower door.

Is a duct leakage test required?

In many areas, energy codes require testing for new homes and some HVAC replacements. Utility rebate programs often require it too.

Can a duct leakage test damage my ducts?

No. The test pressure is modest, about what the system sees during normal operation.

The bottom line

A duct leakage test turns guesswork into numbers. It tells you how leaky your ducts are, whether the leaks waste energy, and whether sealing worked. Test before and after any significant sealing job, ask for leakage to outside if energy savings are the goal, and use the results to target the biggest leaks first. For the bigger picture of duct performance, see the ENERGY STAR duct sealing page.