Gas dryer venting safety matters more than most homeowners realize. An electric dryer’s exhaust is hot, moist and full of lint. A gas dryer’s exhaust is all of that plus the products of combustion, including small amounts of carbon monoxide. That’s why a gas dryer must always vent outdoors through a tight, properly installed duct, and why a blocked or disconnected vent is a carbon monoxide risk as well as a fire risk.
This guide covers seven essential rules for gas dryer venting, the warning signs to watch for, and what to do if something goes wrong.
Key takeaways
- Gas dryers must always vent outdoors; never use an indoor vent kit.
- Use rigid or semi-rigid metal duct with tight connections.
- Clean the vent at least once a year; blockages can push exhaust back into the house.
- Install CO alarms on every level and near sleeping areas.
In this guide
Rule 1: Always vent outdoors
Never use an indoor dryer vent kit with a gas dryer. Combustion gases, including carbon monoxide, must go outside. See indoor dryer vent.
Rule 2: Use metal duct
Use rigid metal duct for the vent run and a listed metal transition duct. Plastic and vinyl ducts are prohibited. See rigid vs flexible dryer vent.
Rule 3: Keep connections tight
Leaky or disconnected joints release exhaust into the laundry room, walls or attic. Secure joints with foil tape or clamps, and check behind the dryer regularly.
Rule 4: Keep the run within limits
Follow the dryer manufacturer’s maximum length and the IRC’s 35-foot rule, reduced for elbows. Use our dryer vent length calculator.
Rule 5: Clean regularly
Lint buildup restricts airflow, which can cause the dryer to overheat and push exhaust back. Clean the full vent at least once a year. See our main guide, how to clean a dryer vent.
Rule 6: Install CO alarms
Install carbon monoxide alarms on every level of the home and outside sleeping areas, following the manufacturer’s instructions. See furnace carbon monoxide.
Rule 7: Have gas work done properly
Gas connections should be made by a qualified installer using an approved connector and a shutoff valve. Check for leaks after any move or installation.
Warning signs
- A CO alarm sounds.
- Headache, dizziness or nausea while doing laundry.
- A burning smell or a smell of gas.
- The laundry room is unusually hot or humid.
- Clothes take much longer to dry.
- Soot near the dryer or vent.
If a CO alarm sounds or you smell gas, leave the house and call 911 or your gas company from outside.
Gas vs electric dryer venting
| Gas dryer | Electric dryer | |
|---|---|---|
| Vent outdoors required | Always | Yes, unless ventless model |
| Combustion gases | Yes | No |
| CO risk if vent blocked | Yes | No |
| Lint fire risk | Yes | Yes |
See the USFA’s dryer safety guidance.
What makes gas dryer exhaust different
A gas dryer heats air with a burner, usually using natural gas or propane. Combustion produces carbon dioxide, water vapor and small amounts of carbon monoxide, which are carried out with the hot, linty exhaust. In normal operation, with a clean, tight gas dryer vent to the outdoors, those gases leave the house. When the vent is blocked, crushed, disconnected or too long, exhaust can back up and leak into the laundry room or walls.
Inspect your gas dryer vent: a 10-minute check
- Look behind the dryer. Is the transition duct metal, intact, short and connected at both ends?
- Check for crushing. Is the duct squashed against the wall?
- Look at the gas connection. Is there a shutoff valve and an approved flexible gas connector, not old copper tubing or a kinked line?
- Go outside. Run the dryer on high heat. Does the hood flap open fully with strong, warm airflow?
- Check the hood. Is it free of lint, nests and screens?
- Check CO alarms. Is there one on this level of the home, and does it pass its test?
If any check fails, fix it before running more loads.
Professional checks worth asking for
When you have the vent cleaned or the dryer serviced, ask the technician to:
- Measure airflow or pressure at the vent.
- Inspect hidden joints with a camera if the run is concealed.
- Check the burner flame and ignition.
- Test for gas leaks at connections.
- Check for carbon monoxide near the dryer while it runs.
Moving or installing a gas dryer
Moving a gas dryer is when problems often start: the transition duct gets crushed and the gas connector gets kinked or stressed. When moving or installing:
- Turn off the gas supply valve first.
- Use a new, listed flexible gas connector rather than reusing an old one.
- Check every gas joint for leaks with a leak detection solution, never a flame.
- Install a new metal transition duct.
- Push the dryer back gently and recheck the duct.
Many people hire a qualified installer for gas connections; local codes may require it.
Gas dryers in closets and small rooms
Gas dryers installed in closets or small laundry rooms need enough air for combustion, which the manufacturer specifies. Louvered doors or makeup air openings may be required. Never block these openings with storage.
Following these gas dryer venting safety rules protects against both of a gas dryer’s main risks: lint fires and carbon monoxide.
Gas dryer venting safety FAQ
Can a gas dryer cause carbon monoxide?
Yes, if the vent is blocked, disconnected or vented indoors.
Can a gas dryer be vented indoors?
No, never.
What duct should a gas dryer use?
Rigid metal for the run and a listed metal transition duct.
How often should a gas dryer vent be cleaned?
At least once a year, more often with heavy use.
